BookTitleMAGNET_GENERAL_CATALOG_2019

Summary

MAGNET_GENERAL_CATALOG_2019

Model EPTW PERMANENT ELECTROMAGNETIC MICROPITCH CHUCK[Application]Suitable for precision grinding on grinders and for holding thinPowersavingMinimaland thick workpieces having a large area.[Features]heatgenerationSide stopper Back stopper Power cord 2 ? 3 m●Thanks to finer pole pitches on the chuck work face, thesechucks hold thin and wide workpieces firmly.●Since electricity is supplied momentarily only to control themagnetomotive force when mounting/demounting a workpiece,little heat is generated internally to maintain accuracy.L 1●Since electricity needs not be supplied continuously evenwhile holding a workpiece, the running cost is very low.EPTW-1530●Since the holding power is maintained in the event of power8L 28failure and cable breakage, safety is secured.[mm(in)]ModelNominal SizeWork Face Pole Pitch Mounting Face Height PowerElectroVoltage MassB? L? t Be P B? L? h HCordChuck MasterEPTW-1530 150(5.90)×300(11.8) 300(11.8) 20150(5.90)(0.78) 125(4.92)300(11.8) 18 9529kg/ 63 lb148(5.82) 2mEPTW-1545 150(5.90)×450(17.7) 450(17.7) 450(17.7) (0.70)(3.74)44kg/ 97 lb4(0.8+3.2)(78.7)EPTW-2040 200(7.87)×400(15.7) 400(15.7)200(7.87) 173(6.81) 0.15 198(7.79) 90 VDCEPS-215B25(0.03+0.12)(0.98)65kg/143 lbEPTW-2050 200(7.87)×500(19.6) 500(19.6) 500(19.6) 20 12082kg/180 lb3mEPTW-2560 250(9.84)×600(23.6) 250(9.84) 217(8.54) 248(9.76) (0.78)(4.72)123kg/271 lb600(23.6)600(23.6)(118)EPTW-3060300(11.8)×600(23.6)300(11.8)269(10.5)298(11.7)147kg/324 lb※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.PBeB 2th1EPT / EPT-LW / EPT-H / EPTW / EPTW-N / EPZ-UChuck controllerrequired additionallyB 1HELECTROMAGNETICCHUCKSCHUCKCONTROLLERSPERMANENTMAGNETIC CHUCKSPERMANENTELECTROMAGNETIC CHUCKSModel EPTW-N PERMANENT ELECTROMAGNETIC MICROPITCH CHUCKPowersavingModel EPZ-U TILT TYPE PERMANENT ELECTROMAGNETIC CHUCKEPZ-1030UFEnvironmentallyfriendlyEPTW-N2040Power cord 2 mBeP1 H1BLeL 1L 2Back stopper1[Application]Suitable for angle grinding on grinders. Easy to install.[Features]●The rotary shaft with scale facilitates angle setting. (Anangle can be set as desired in a range of 90°forwardand 90°backward.)●Since electricity is supplied momentarily only to controlthe magnetomotive force when mounting/demounting aworkpiece, little heat is generated internally to enablehighly precise machining.●Since electricity needs not be supplied continuously evenwhile holding a workpiece, the running cost is very low.●Since the holding power is maintained in the event of powerfailure and cable breakage, safety is secured.●A resin-bonded structural face plate having littleenvironmental burden is employed.[mm(in)]ElectroChuck Master80 368(14.4) 22kg/ 48 lb130(3.15)24kg/ 52 lb50 29 1415(5.11)418(16.4) 90 VDC 30kg/ 66 lb EPS-215B(1.96)(1.14)(0.55)95 (0.59)14537kg/ 81 lb(3.74)(5.70)Work Face Pole Pitch Tilt Base Length HeightModel Nominal SizeVoltage MassB? L? Be Le H? P B? ?? ?? G h? h? L? H?EPZ-1025UF 100(3.93)×250(9.84) 250(9.84) 211(8.30)11(2+9)100(3.93) 78(3.07)EPZ-1030UF 100(3.93)×300(11.8)255(10.0) 0.43(0.07+0.35)100100EPZ-1230UF 120(4.72)×300(11.8)120(4.72) 300(11.8) 96(3.78)240(9.44) (3.93) 14(2+12) (3.93)EPZ-1530UF 150(5.90)×300(11.8)150(5.90) 120(4.72)0.55(0.07+0.47)EPZ-1545UF 150(5.90)×450(17.7) 450(17.7) 408(16.0) 568(22.3) 52kg/114 lb※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.2G2h2B1h2H[Application]Suitable for grinding of thin and smallworkpieces.[Features]●Generates strong holding power onworkpieces of□25 mm and larger.●Instead of the conventional magneticpole longitudinal patterns, the transversemagnetic pole patterns are used.●A resin-bonded structural face platehaving little environmental burden isemployed.[mm(in)]ModelNominal SizeWork Face Pole Pitch Mounting Face Height PowerElectroVoltage MassB? L? t Le P B? L? h HCordChuck MasterEPTW-N1530 150(5.90)×300(11.8) 300(11.8) 261(10.2)150(5.90) 148(5.82)4(1+3)250.15(0.98)(0.04+0.11)30kg/ 66 lb2mEPTW-N1545 150(5.90)×450(17.7) 450(17.7) 397(15.6) 464(18.2) 10045kg/ 99 lb(78.7)EPTW-N2040 200(7.87)×400(15.7) 400(15.7) 349(13.7)414(16.2) 20 (3.93) 52kg/114 lb200(7.87) 198(7.79) 180 VDCEPTW-N2050 200(7.87)×500(19.6) 500(19.6) 449(17.6) 514(20.2) (0.78)65kg/143 lb3mEPTW-N2560 250(9.84)×600(23.6) 250(9.84) 246(9.68) 110107kg/235 lb600(23.6) 549(21.6)614(24.1)(118)EPTW-N3060 300(11.8)×600(23.6) 300(11.8) 296(11.6) (4.33)128kg/282 lbEPS-W215B※The chuck controller and clamp parts are not included.※The KANETEC chucks work best when a KANETEC chuck controller is used.※Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes. If on/off operations are repeated frequently, the chucks may be damaged by overheat.PowersavingMinimalheatgenerationMinimalheatgenerationChuck controllerrequired additionallyEnvironmentallyfriendlyChuck controllerrequired additionallyBSidestopperB 2Hh tPL 1LeL 2PowercordBLOCKSFOR MCVACUUMCHUCKSPROMELTA*SYSTEMSINE BARCHUCKSBLOCKS, HOLDERS,MINI CHUCKSHOLDINGTOOLSMEASURINGTOOL HOLDERSMAGNETICHOLDERSMAGNETICTOOLS38